60 Amp Solar Charge Controller

60 Amp Solar Charge Controller

Product name:PWM solar charge controller 60A
Model No.:NC 12/24- 60D
Working principle:PWM Solar Charge Controller is a photovoltaic (PV) charge controller that tracks the PV array to deliver the available current for charging batteries. When charging, the Controller regulates battery voltage and output current based on the amount of energy available from the PV array and state-of-charge of the battery.

inquiry

Details

60 amp solar charge controller information

Manual PWM 60 amp solar charge controller 

This is a kind of intelligent, multi-purpose solar charge and discharge controller.

The family use the fixed LCD display, with a very friendly interface; various control parameters can be flexibly set, fully meet your various application requirements.

Technical Data for NC 60amp solar charge controller

image021.jpg

Model

NC12/24-60D

Input

PV input voltage

≤50V 

Rated charge current

60A

Output

System voltage

12V/24V Auto or 48V

HVD

16.00V×1×2×3×4

Rated current

60A

No-load loss

≤14mA

Charge loop voltage drop

≤0.22V

Discharge loop voltage drop

≤ 0.12V

Charging mode

PWM 4-stage(bulk, absorption,float, equalized)

Voltage of float charging

13.8(13V~15V)×1/×2/×3/×4

Voltage of absorption charging

14.4V(13V~15V) ×1/×2/×3/×4

Duration of absorption charging

2hs

LVD

10.8V(10V~14V) ×1/×2/×4

LVR

12.6V(10V~14V) ×1/×2/×4

Load working mode

Regular control mode

Light control with switch-off point at night and switch-on point before dawn

Light control mode

Light control voltage

5V(1V~10V) ×1/×2/×4

Battery type

GEL, SLD, FLD and USr(default)

Other

Buttons

LCD, 3 buttons

Heat sink

AL alloy heat sink

Wiring

PCB terminal, ≤25mm2

Working temperature

-20 ~ +55 °C

Storage temperature

-30 ~ +65 °C

Working humidity

10% ~ 90%, no condensation

Dimension

188 x 133 x 51.5 mm

Net Weight

735g

IP grade

IP30

Optional function

Remote communication,TTL, standard ModBus protocol

Accessory

Temperature sensor

Connection diagram


Packaging for pwm solar charge controller 

About 60 amp solar charge controller 

1. Simple visible LCD display shows live parameters of power system, monitor and check system status.

2. All the controlling parameters can be reset flexibly to satisfy your different needs.

3. 12V 24V auto switch, and automatically break off when the battery is not sufficient to power loads, make sure battery will not drain off.

4. Integrated multiple protection against overcharge, over discharge, over load, short circuit and reverse polarity, safely protect your battery.

5. Temperature compensation function, the controller can automatically adjust the charge parameters of battery by environment temperature to prolong the service life of battery.

Application for solar charge controller

Our Advantage

Our factory


Our market

Certification

image017.jpg


FAQ

Q:What is a Solar Charge Controller? Why do I need one?

A charge controller, or charge regulator is basically a voltage and/or current regulator to keep batteries from overcharging. It regulates the voltage and current coming from the solar panels going to the battery. Most "12 volt" panels put out about 16 to 20 volts, so if there is no regulation the batteries will be damaged from overcharging. Most batteries need around 14 to 14.5 volts to get fully charged.

Q:Do I always need a charge controller?

Not always, but usually. Generally, there is no need for a charge controller with the small maintenance, or trickle charge panels, such as the 1 to 5 watt panels. A rough rule is that if the panel puts out about 2 watts or less for each 50 battery amp-hours, then you don't need one.

Q: Why 12 Volt Solar Panels are 17 Volts?

The obvious question then comes up - "why aren't panels just made to put out 12 volts". The reason is that if you do that, the panels will provide power only when cool, under perfect conditions, and full sun. This is not something you can count on in most places. The panels need to provide some extra voltage so that when the sun is low in the sky, or you have heavy haze, cloud cover, or high temperatures*, you still get some output from the panel. A fully charged "12 volt" battery is around 12.7 volts at rest (around 13.6 to 14.4 under charge), so the panel has to put out at least that much under worst case conditions.

Q: What's A PWM solar charge controller ?

A PWM solar charge controller stands for “Pulse Width Modulation”. These operate by making a connection directly from the solar array to the battery bank. During bulk charging, when there is a continuous connection from the array to the battery bank, the array output voltage is ‘pulled down’ to the battery voltage. As the battery charges, the voltage of the battery rises, so the voltage output of the solar panel rises as well, using more of the solar power as it charges. As a result, you need to make sure you match the nominal voltage of the solar array with the voltage of the battery bank. *Note that when we refer to a 12V solar panel, that means a panel that is designed to work with a 12V battery. The actual voltage of a 12V solar panel, when connected to a load, is close to 18 Vmp (Volts at maximum power). This is because a higher voltage source is required to charge a battery. If the battery and solar panel both started at the same voltage, the battery would not charge.


Hot Tags: 60 amp solar charge controller, China, manufacturers, suppliers, factory, wholesale

Feedback

Subscribe to our email list
Sign up with your name and email to get the latest proway updates, exclusive access to promotions, sales events, pre-order sales & more!
Connect with Solarway
Become our fan, follow us & subscribe for the latest updates and deals
QR Code
  • About Us
  • Product
  • News
  • Knowledge
  • Contact Us
  • Copyright © Jiaxing Solarway New Energy Co.,Ltd All Rights Reserved.